Experimental study of controlling tip clearance flow in a pump-jet propulsor

Ruilin HAN; Haiting YU; Hongxing HUA; Huiyao LI; Xiuchang HUANG; Xiaoqian DONG

doi:10.19693/j.issn.1673-3185.02419

Zhongguo Jianchuan Yanjiu (Feb 2023)

Experimental study of controlling tip clearance flow in a pump-jet propulsor

Ruilin HAN,
Haiting YU,
Hongxing HUA,
Huiyao LI,
Xiuchang HUANG,
Xiaoqian DONG

Affiliations

Ruilin HAN: State Key Laboratory of Mechanical System and Vibration, Institute of Vibration Shock and Noise, Shanghai Jiao Tong University, Shanghai 200240, China
Haiting YU: State Key Laboratory of Mechanical System and Vibration, Institute of Vibration Shock and Noise, Shanghai Jiao Tong University, Shanghai 200240, China
Hongxing HUA: State Key Laboratory of Mechanical System and Vibration, Institute of Vibration Shock and Noise, Shanghai Jiao Tong University, Shanghai 200240, China
Huiyao LI: State Key Laboratory of Mechanical System and Vibration, Institute of Vibration Shock and Noise, Shanghai Jiao Tong University, Shanghai 200240, China
Xiuchang HUANG: State Key Laboratory of Mechanical System and Vibration, Institute of Vibration Shock and Noise, Shanghai Jiao Tong University, Shanghai 200240, China
Xiaoqian DONG: Collaborative Innovation Center for Advanced Ship and Deep-Sea Exploration, Shanghai 200240, China

DOI: https://doi.org/10.19693/j.issn.1673-3185.02419
Journal volume & issue: Vol. 18, no. 1
pp. 141 – 151

Abstract

Read online

ObjectiveThis paper aims to suppress the adverse effects of tip clearance flow on the hydrodynamic performance and unsteady excitation force of a pump-jet propulsor. MethodAs for the pre-swirl stator pump-jet propulsor, an annular flexible seal structure closely matched with a rotor tip ring is used to study the validity of suppressing the clearance flow on the rotor tip. The rotor thrust and torque of the propulsor are measured by keeping the shroud approximately rigidly fixed, enabling the rotor open water efficiency to be obtained. In addition, the point of cavitation inception at each design condition is observed and recorded carefully with the help of a high-power stroboscope, and the cavitation inception curves of the propulsor with/without tip clearance are obtained through calculation. Finally, tests of shaft vibration acceleration on the pump-jet propulsor with/without tip clearance are conducted under conditions of cavitation and non-cavitation in order to evaluate the effects of diminishing tip clearance. ResultsThe results show that the thrust and torque of the rotor of the pump-jet propulsor with a flexible seal structure are significantly increased, which in turn renders open water efficiency significantly increased at low and medium advance coefficients, unchanged near the design point and slightly decreased at the high advance coefficient. Moreover, the cavitation performance of the pump-jet propulsor without clearance is better at a wide range of advance coefficient, 0.85 <J< 1.40, near the design point. In addition, compared with a pump-jet propulsor with clearance, the amplitude of axial vibration acceleration of the shaft equipped with a pump-jet propulsor without tip clearance is significantly reduced at most characteristic frequencies.ConclusionThe results of this study demonstrate that using a flexible seal structure to suppress tip clearance flow has a positive effect on improving open water efficiency at low and medium advance coefficients, optimizing cavitation performance at the design point and suppressing the shafting vibration of the propulsor.

Published in Zhongguo Jianchuan Yanjiu

ISSN: 1673-3185 (Print)
Publisher: Editorial Office of Chinese Journal of Ship Research
Country of publisher: China
LCC subjects: Naval Science: Naval architecture. Shipbuilding. Marine engineering
Website: http://www.ship-research.com/indexen.htm

About the journal

Abstract

Keywords